Ride Command® Mount Kit

P/N 2884731

1 Before You Begin

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.

3 Required Sold Separately

Only parts for installation of the are included. For complete installation, the following additional kit is required (sold separately):

  • Ride Command® Display, P/N 2884072

4 Kit Contents

Ref

Qty

Part Description

P/N Available Separately
1 1 Harness–Antenna (see Harness Detail section) 2415037
2 1 Harness–USB (see Harness Detail section) 2415322
3 1 Harness–Ride Command® (see Harness Detail section) 2415489
4 1 Antenna–Mast 4014849
5 1 Camera–Rear 4015873
6 1 Camera–Front 4016639
7 1 Strap–Ground, Antenna 4017533
8 1 Antenna–GPS 4017533
9 1 Sensor–Air Temperature Gauge 4018205
10 1 Antenna–Vehicle-to-Vehicle (V2V) 4018713
11 1 Mount–Antenna 4019254
12 1 Bracket–Ride Command® Display 5266577
13 1 Bezel–Ride Command® Display 5455347
14 1 Bezel–Button, Ride Command® Display 5455574
15 2 Screw–Hex Flange Thread Form, (M6 x 1.0 x 20 mm) 7518529
16 3 Screw–Torx® Button Head, (M6 x 1.0 x 12 mm) 7519063
17 1 Nut–Hex Flange, M5 x 0.8 mm 7547437
18 2 Rivet–Push-Pin 7661855

5 Harness Detail

Antenna Harness 1

Ref

Part Description

Connects to
1F Antenna Connector Ride Command® Display (sold separately)
1F Antenna Mount Ring Connector Antenna Mount 11

Example: 16F = 16 pin, Female / 16M = 16 pin, Male (Male terminal fits inside female terminal)

USB Harness 2

Ref

Part Description

Connects to
6F USB Connector Ride Command® Display (sold separately)

Example: 16F = 16 pin, Female / 16M = 16 pin, Male (Male terminal fits inside female terminal)

Ride Command® Harness 3

Ref

Part Description

Connects to
4F Camera Connector, Front Front Camera 6
2F Air Temperature Sensor Connector Air Temperature Gauge Sensor 9
1M Coaxial Connector V2V Antenna 10
1F Positive (+) Ring Terminal Accessory Terminal Bar
1F Ground (–) Ring Terminal Accessory Terminal Bar
2F Subwoofer Connector Subwoofer (sold separately)
2F Speaker Connector, Left Speaker (sold separately)
4M Rear Audio Connector Rear Speaker Harness (sold separately)
32F Power Connector, Ride Command® Ride Command® Display (sold separately)
1F V2V Connector Ride Command® Display (sold separately)
16F Display Connector, Ride Command® Ride Command® Display (sold separately)
2F Speaker Connector, Left Speaker (sold separately)
16M Infotainment Connector Chassis Electrical Harness
1M Amplifier Ground Connector Amplifier (sold separately)
23F Amplifier Connector Amplifier (sold separately)

Example: 16F = 16 pin, Female / 16M = 16 pin, Male (Male terminal fits inside female terminal)

6 Tools Required

  • Safety Glasses

  • Center Punch

  • Deburring Tool

  • Drill

  • Drill Bit:

    • (6 mm)

    • (10.5 mm)

    • (17 mm)

    • (19 mm)

    • Step Drill Bit

  • Pick and Hook Set

  • Pliers, Push Pin Rivet

  • Push Dart (Panel Clip) Tool

  • Ruler

  • Screwdriver Set, Torx®

  • Socket Set, Metric

  • Socket Set, Torx® Bit

  • Tape Measure

  • Torque Wrench

  • Wrench Set, Metric

7 Consumables Required

  • Tape, Electrical

8 Important

Your is exclusively designed for your vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

9 Installation Instructions

9.1 Vehicle Preparation

9.1.1 General

  1. Shift vehicle transmission into PARK.

  2. Turn key to OFF position and remove from vehicle.

9.1.2 Seat Removal

NOTICE
Driver seat shown; passenger seat similar.

  1. Reach between seat and backrest. Pull up on lever, located behind seat to disengage seat latch.

9.1.3 Battery Disconnect

  1. Loosen fastener on negative (-) terminal clamp and move away from battery.

9.1.4 Center Hood Panel Removal

  1. Turn quarter-turn fasteners to unlock hood from vehicle.

  2. Move hood forward to remove from vehicle.

9.1.5 Dashboard Storage Removal

NOTICE
Storage bin shown; audio head unit bezel similar.

  1. Remove two push-pin rivets from top of storage compartment.

  2. Tilt storage compartment rearward to remove from dashboard.

9.1.6 Dashboard Top Removal

  1. Remove four dashboard fasteners.

  2. Lift dashboard upwards to remove from vehicle.

9.1.7 Passenger Dashboard Storage Removal

  1. Remove two push-pin rivets and remove passenger-side dashboard storage bin.

9.1.8 Grille Removal

  1. Push two tabs down to remove grille from front fascia.

9.2 Accessory Installation

Front Camera Installation

  1. Put front camera 6 into mounting hole, located in grille trim. Clips on camera sides will snap into place when fully seated.

Rear Camera Installation

  1. Drill one (19 mm) hole in rear fascia.

    MEASUREMENT

    Measurement A:

    (19 mm)

  2. Put rear camera harness through hole and push rear camera 5 until it snaps into place.

  3. Reach behind fascia from either side to located chassis electrical harness. Install rear camera to chassis electrical harness.

Template Placement

  1. Detach template page located at the end of this instruction.

  2. Locate REFERENCE DIMENSION on each template page.

    Verify REFERENCE DIMENSION is exact and template(s) were printed to proper scale.

    NOTICE

    If REFERENCE DIMENSION is not exact, reprint template page from electronic file. Adjust print setting to “Actual Size” to obtain 1:1 scale.

    Electronic file available from your Authorized Dealer.

  3. Mark three locations on top of hood for alignment pin and antenna mounting post.

  4. Drill at each marked location.

    IMPORTANT
    Control tool depth. Ensure tool is clear of all other parts and components to prevent damage to vehicle.
    MEASUREMENT

    Alignment Pin Hole A:

    (6 mm)

    MEASUREMENT

    Antenna Mounting Post Hole B:

    (10.5 mm)

    MEASUREMENT

    V2V Mounting Post Hole C:

    (17 mm)

V2V Antenna Installation

  1. Remove nut from V2V antenna assembly.

  2. Put V2V antenna 10 harness through hole in upper fender panel. Install antenna to upper fender with nut, removed in previous step. Tighten nut until it is fully seated against fender panel.

Ride Command® Display Installation (Sold Separately)

  1. Align display mount 12 with vehicle frame and install with two fasteners 15.

    TORQUE

    Display Mount Fasteners 15:

    8 ft-lbs (10 N·m)

  2. Install Ride Command® to display mount with three fasteners16. Torque three fasteners to specification.

    TORQUE

    Display Fasteners 16:

    40 in-lbs (4 N·m)

  3. Install bezel 14 onto Ride Command® display.

Ride Command® Harness 3 Routing

NOTICE
Audio accessories referenced in this section are sold separately.

  1. Remove two nuts from Polaris Pulse® bar.

  2. Install negative 1F (black) and positive 1F (red) ring terminals with two retained nuts. Torque nuts to specification.

    TORQUE

    Polaris Pulse® Nuts:

    35 in-lbs (4 N·m)

  3. Install fuse relay onto firewall.

  4. Install coaxial connector 1M to V2V antenna.

  5. Put two connectors (front camera and temperature sensor) through opening in radiator shroud, located below right-hand headlight.

  6. Remove cap from front camera connector 4F and install to front camera.

  7. Install temperature sensor connector 2F to air temperature sensor 9. Install harness along winch mount with attached edge clips. Install sensor 9 with attached push-pin.

  8. Put Ride Command® display and audio connectors through firewall grommet. Attach harness to chassis harness with attached cable tie.

  9. Carefully pull connectors through firewall grommet.

  10. Install the following connectors to the back of the Ride Command® display.

  11. Put right-hand speaker connector 2F over vehicle frame, between outer fender panel. Connect to speaker, if equipped.

  12. Install subwoofer connector 2F to subwoofer, if equipped.

  13. Install rear audio connector 4M to rear audio harness, if equipped.

  14. Put left-hand speaker connector 2F over vehicle frame, between outer fender panel. Connect to speaker, if equipped.

  15. Install connector 16M to chassis electrical harness.

  16. Install amplifier connector 23F to amplifier, if equipped.

USB Harness 2 Routing

  1. Install USB connector 6F to back of Ride Command® display.

  2. Open storage bin.

  3. Put USB harness through hole in storage bin and install grommet within hole.

AM/FM Antenna Installation

  1. Put antenna mount in upper fender. Antenna mount will snap into place when fully seated.

  2. Remove plastic nut from mounting post.

  3. Put ground strap 7 over mounting post and install with plastic nut removed from mounting post.

  4. Remove and keep one fastener from the firewall.

  5. Install ground strap 7 with retained fastener. Torque fastener until fully seated.

  6. Install antenna mast 4 into antenna mount 11.

AM/FM Antenna Harness 1 Routing

  1. Put antenna mount ring connector 1F over mounting post and install with nut 17.

  2. Put antenna connector 1F through firewall grommet.

  3. Pull antenna connector from firewall grommet towards Ride Command® display.

  4. Install antenna connector 1F to Ride Command® display.

9.3 Vehicle Reassembly

9.3.1 Battery Connect

  1. Install negative (-) terminal clamp with fastener. Torque fastener to specification.

    TORQUE

    Terminal Clamp Fastener:

    60 in-lbs (6.5 N·m)

9.3.2 Seat Installation

NOTICE
Driver seat shown; passenger seat similar.

  1. Put seat in installed position. Align latch with plunger on vehicle.

9.3.3 Audio Test

  1. Turn vehicle on.

  2. Turn Ride Command® display on and test audio connection.

9.3.4 Passenger Dashboard Storage Installation

  1. Install dashboard storage bin with two push-pin rivets.

9.3.5 Dashboard Top Installation

  1. Install dashboard on top of front dashboard panel. Make sure top dashboard clips engage with front dashboard.

  2. Install dashboard with four dashboard fasteners.

    TORQUE

    Dashboard Fasteners:

    8 ft-lbs (11 N·m)

9.3.6 Ride Command® Display Bezel Installation

  1. Align display bezel with Ride Command® and dashboard. Install with two push-pin rivets.

9.3.7 Grille Installation

  1. Install grille into front fascia. Make sure two tabs engage with fascia.

10 Instruction Feedback Form

A feedback form has been created for the installer to provide any comments, questions or concerns about the installation instructions. The form is viewable on mobile devices by scanning the QR code or by clicking HERE if viewing on a PC.