Dash Bags Kit

P/N 2884989

1 Before You Begin

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.

2 Disclaimer Accessory Weight

When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label). Ask an authorized dealer for specific weight information if you need assistance. It is the owner’s responsibility to use the Polaris Slingshot Accessories website as a tool for limiting the amount of accessories, based on maximum allowable vehicle weight requirements. It may be a violation of the Clean Air Act or the NHTSA regulations to disregard these requirements.  For a complete listing of the accessories that are available for your vehicle, please contact your authorized dealer or visit the online store web site:
Web Address (United States): http://www.polaris.com/en-us/slingshot/shop/accessories .

4 Kit Contents

Ref

Qty

Part Description

P/N Available Separately
1 1 Dash Bag, RH 2690272
2 1 Dash Bag, LH 2690271
3 6 Push-Pin Rivet, 0.315–0.325 X 0.787 in 7661855

5 Tools Required

  • Safety Glasses

  • Drill

  • Drill Bit:

    • 11/32 in (8.5 mm)

  • Marking Pen

  • Push Dart (Panel Clip) Tool

  • Socket Set, Hex Bit, Metric

  • Socket Set, Torx® Bit

  • Torque Wrench

6 Important

Your is exclusively designed for your vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

7 Installation Instructions

7.1 Vehicle Preparation

7.1.1 General

  1. Park vehicle on a flat surface.

  2. Shift vehicle to NEUTRAL.

  3. Press START/STOP button to turn vehicle OFF.

  4. Apply parking brake.

  5. Remove key fob from proximity of vehicle.

7.1.2 Remove Windshield

NOTICE
Windshields vary in size and shape but all mount to the same mounting points.

  1. Remove and keep three fasteners A from base of windshield B.

  2. If equipped, remove and keep screw, washer and O-ring from center windshield mount.

  3. Remove windshield and carefully set aside.

7.1.3 Remove Mirrors

  1. Remove and keep two mirror mounting screws.

  2. Remove and carefully set aside mirror assembly.

  3. Repeat for opposite side mirror.

7.1.4 Remove Upper Dash

Remove Upper Dash Painted Panels (If Equipped)

  1. Remove and keep upper dash painted panels by lifting from front edges to release clips.

Remove Side Trim Panels
NOTICE
Left side shown; right side similar.

  1. Remove and keep two screws A and two push-pin rivets B from side trim panel C.

  2. Remove side trim panel C and carefully set aside.

Remove Upper Dash Panel

  1. Remove and keep eight screws A from upper dash panel.

  2. If equipped, disconnect dash tweeter speakers from main vehicle harness.

  3. Lift front edge of upper dash panel to release clips. Lift off upper dash panel and carefully set aside.

7.2 Accessory Installation

  1. Set right 1 and left 2 bags in place on upper dash panel.

  2. Open bags and mark hole locations on dashboard with a light colored marking device.

  3. Drill six 11/32 in (8.5 mm) holes in center of marked locations.

  4. Set bags in place and install six push rivets 3 into holes.

7.3 Vehicle Reassembly

7.3.1 Install Upper Dash

Install Upper Dash Panel

  1. If equipped, connect dash tweeter speakers to main vehicle harness.

  2. Set upper dash panel in place and loosely install eight retained screws A.

  3. Torque eight screws to specification.

    NOTICE
    Inner and outer fasteners have different torque specifications.
    TORQUE

    Inner Upper Dash Panel Screws A:

    65 in-lbs (7.4 N·m)

    TORQUE

    Outer Upper Dash Panel Screws B:

    36 in-lbs (4 N·m)

Install Side Trim Panels

  1. Set side trim panel C in place and loosely install two retained screws A and install two retained push pin rivets B.

  2. Torque two screws to specification.

    TORQUE

    Side Trim Panel Screws A:

    10 in-lbs (1.1 N·m)

  3. Repeat steps 1–2 for opposite side trim panel.

7.3.2 Install Mirrors

  1. Set mirror in place and attach with two mirror mounting screws.

  2. Torque mounting screws to specification.

    TORQUE

    Mirror Mount Screws:

    35 ft-lbs (47 N·m)

  3. Repeat for opposite side mirror.

7.3.3 Install Windshield

  1. Set windshield B in place and attach with retained fasteners A.

  2. Torque fasteners to specification (if applicable).

    TORQUE

    Windshield Threaded Fastener:

    13 in-lbs (1.4 N·m)

  3. If equipped, install screw, washer and O-ring into center windshield mount. Torque screw to specification.

    TORQUE

    Windshield Center Mount Screw:

    13 in-lbs (1.4 N·m)

8 Cleaning and Care

Cleaning

Use a non-abrasive cloth and mild soap to clean bags

Care

Leave zippers open when bag is not in use to allow moisture inside to escape.

9 Instruction Feedback Form

A feedback form has been created for the installer to provide any comments, questions or concerns about the installation instructions. The form is viewable on mobile devices by scanning the QR code or by clicking HERE if viewing on a PC.