Heat Shield Kit

P/N 2889217-XXX

1 Before You Begin

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.

3 Kit Contents

NOTICE
XXX = Indian Motorcycle® color code (For example: 266 = Black)

Ref

Qty

Part Description

P/N Available Separately
1 6 Clamp-Worm Drive 2.25 in Dia. 7082310
2 1 Shield, Catalytic Converter 1263415–XXX
3 1 Shield, Rear 1263414–XXX
4 1 Shield, Front 1263413–XXX

4 Tools Required

  • Safety Glasses

  • Socket Set, Hex Bit, Metric

  • Socket Set, Metric

  • Torque Wrench

5 Important

Your is exclusively designed for your vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

6 Installation Instructions

6.1 Vehicle Preparation

6.1.1 General

  1. Park motorcycle on a flat surface, fully extend kickstand, and make sure vehicle is stable.

  2. Turn key or ignition switch to OFF position and remove key. If equipped with keyless fob, remove fob from proximity of vehicle.

6.2 Removal Procedure

WARNING

Engine and exhaust components get hot and remain hot for a period of time after the engine is stopped. Wear insulated protective clothing or wait for components to cool sufficiently before working on the machine.

IMPORTANT
Protect all finished and painted surfaces during these operations.

Remove RH Foot Control

  1. Remove and keep the two fasteners A that secure the RH foot control to the motorcycle frame.

  2. Support the RH foot control with a strap or similar equipment.

    IMPORTANT
    Make sure to support and keep the RH foot control upright as the brake line will remain connected.

Remove Rear Heat Shield

  1. Remove and discard the two worm-drive clamps B.

  2. Remove the rear heat shield C.

Remove Front Heat Shield

  1. Remove and discard the three worm-drive clamps B.

    NOTICE
    Front heat shield hidden from image for illustration clarity.

  2. Remove the front heat shield D.

Remove Catalytic Converter Heat Shield

  1. Remove and discard the one worm-drive clamp B.

    NOTICE
    Catalytic converter heat shield hidden from image for illustration clarity.

  2. Remove and keep the two fasteners E that secure the heat shield to the motorcycle.

  3. Remove the catalytic converter heat shield F.

6.3 Accessory Installation

IMPORTANT
Protect all finished and painted surfaces during these operations.

Install Catalytic Converter Heat Shield

  1. Open and insert a new worm-drive clamp 1 on the accessory catalytic converter heat shield 2 as shown.

  2. Open the worm-drive clamp far enough to slip it over the exhaust pipe, and then put the accessory catalytic converter heat shield 2 on the motorcycle.

  3. Install the two heat shield fasteners E and torque to specification.

    TORQUE

    Heat Shield Fasteners E:

    88 in-lbs (10 Nm)

  4. Torque the worm-drive clamp to specification.

    TORQUE

    Worm-Drive Clamp 1:

    31 in-lbs (3.4 Nm)

Install Front Heat Shield

  1. Open and insert three new worm-drive clamps 1 on the accessory front heat shield 4 as shown.

  2. Open the worm-drive clamps far enough to slip them over the exhaust pipe, and then put the accessory front heat shield 4 on the motorcycle. Make sure the clamps are set as shown.

  3. Make sure the seams between the heat shields are aligned, and then torque the worm-drive clamps to specification.

    TORQUE

    Worm-Drive Clamp 1:

    31 in-lbs (3.4 Nm)

Install Rear Heat Shield

  1. Open and insert two new worm-drive clamps 1 on the accessory rear heat shield 3 as shown.

  2. Open the worm-drive clamps far enough to slip them over the exhaust pipe, and then put the accessory rear heat shield 3 on the motorcycle.

  3. Make sure the seams between the heat shields are aligned, and then torque the worm-drive clamps to specification.

    TORQUE

    Worm-Drive Clamp 1:

    31 in-lbs (3.4 Nm)

6.4 Vehicle Reassembly

Install RH Foot Control

  1. Raise the RH foot control into position on the motorcycle.

  2. Install the two fasteners A that secure the RH foot control to the motorcycle frame. Torque the fasteners to specification.

    TORQUE

    RH Foot Control Fasteners A:

    35 ft-lbs (47.5 Nm)

7 Instruction Feedback Form

A feedback form has been created for the installer to provide any comments, questions or concerns about the installation instructions. The form is viewable on mobile devices by scanning the QR code or by clicking HERE if viewing on a PC.