Full-Size RIDE COMMAND+ Plug-In Mount Kit

P/N 2889602

1 Before You Begin

Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.

IMPORTANT

Kit is not compatible with Ride Command® Mount Kit, P/N 2889309.

3 Required Sold Separately

Only parts for installation of the are included. For complete installation, the following additional kit is required (sold separately):

  • 250K RIDE COMMAND+ Plug-In Kit, P/N 2890038

  • Polaris® application is required (available in AndroidTM and Apple® app stores. Search “Polaris®”).

4 Kit Contents

Ref

Qty

Part Description

P/N Available Separately
1 1 Harness, RIDE COMMAND+ Plug-In 2416347
2 1 Grommet, (0.25 X 1 .25 X 0.13 mm), Groove 5418308
3 2 Clip Push Pin, Retaining 7081496
4 1 Cable Tie, Dual Loop 7081916
5 4 Screw - Torx® Pan Head #14 X 3/4 in 7519274

5 Harness Detail

RIDE COMMAND+ Plug-In Harness 1

Ref

Part Description

Connects to
8F Chassis Connector Main Chassis Harness
8M Diagnostic Connector Diagnostic Port
6F Plug-In Connector RIDE COMMAND+ Plug-In

Example: 16F = 16 pin, Female / 16M = 16 pin, Male (Male terminal fits inside female terminal)

6 Tools Required

  • Safety Glasses

  • Drill

  • Drill Bit:

    • Bit Size: 1/4 in (6 mm)

  • Hole Saw:

    • Bit Size: 1 1/4 in (32 mm)

  • Screwdriver Set, Torx®

7 Important

Your is exclusively designed for your vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

8 Installation Instructions

8.1 Vehicle Preparation

8.1.1 General

  1. Park vehicle on flat surface.

  2. Shift vehicle into PARK.

  3. Turn ignition switch to OFF position and remove key.

8.1.2 Underseat Storage Bin Access and Removal

Crew without seat slider

  1. Lift up passenger seat by the edge and pull up to reveal under storage bin.

  2. Remove and keep under storage bin.

  3. Lift second seat up by pulling up on the latch behind the second seat.

  4. Remove and keep second under storage bin.

3 seat with seat slider

  1. Lift seat up

  2. Slide seat forward to access underseat screws. Remove and keep two screws.

  3. In front of the seat, locate two screws. Remove and keep two screws.

  4. Lift up seat by the edges to remove.

  5. Remove and keep second under storage bin.

8.2 Accessory Installation

Storage Bin Preparation

  1. Measure hole from the wall to the center of the hole. Mark drill point.

    MEASUREMENT

    Measurement A:

    1.40 in (35 mm)

    MEASUREMENT

    Measurement B:

    2 in (50 mm)

  2. Drill hole in bottom of storage bin.

    MEASUREMENT

    Measurement:

    1 1/4 in (32 mm)

  3. Measure from the wall to the center of the first hole. Mark drill point.

    MEASUREMENT

    Measurement A:

    1 in (24 mm)

    MEASUREMENT

    Measurement B:

    3.20 in (81 mm)

  4. Measure from the wall to the center of the second hole. Mark drill point.

    MEASUREMENT

    Measurement C:

    1.50 in (37 mm)

    MEASUREMENT

    Measurement D:

    0.70 in (17 mm)

  5. Drill two holes.

    MEASUREMENT

    Measurement:

    1/4 in (6 mm)

RIDE COMMAND+ Plug-In Installation

  1. Install RIDE COMMAND+ Plug-In (sold separately) on four storage bin posts with four screws 5. Tighten until fully seated.

    Do not overtighten.

  2. Install grommet 2 on harness 1 near the plug-in connector 6F.

  3. Put harness 1 connector 6F through 1 1/4 in hole. Install grommet 2 in hole.

  4. Connect plug-in connector to 6F connector.

  5. Route harness 1 under storage bin. Install two push pins 3 in 1/4 in holes.

  6. Unplug diagnostic port 8F from cap on vehicle. Location of port depends on model year.

    • Model Year 2022+

    • Model Year 2021 and older

  7. Connect harness diagnostic connector 8M to recently disconnected diagnostic port 8F.

  8. Connect harness chassis connector 8F to empty cap on vehicle.

8.3 Vehicle Reassembly

8.3.1 Seat and Bin Reassembly

Crew without seat slider

  1. Reinstall both storage bins for both seats.

  2. Close both seats.

3 Seat with seat slider

  1. Reinstall under storage bin.

  2. Reinstall seat with seat slider onto the seat. Make sure that the front bracket fits into the holes of the bracket hinge.

  3. Reinstall the two retained screws in front of the seat. Torque to specification.

    TORQUE

    Screws:

    72 in-lbs (8 N·m)

  4. Slide seat forward to reinstall two retained underseat screws. Torque to specification.

    TORQUE

    Underseat screws:

    72 in-lbs (8 N·m)

  5. Reinstall under storage bin for passenger

  6. Close seats.

9 Operation

Polaris® App

Download the Polaris® App for the Apple or Android device that will be used with RIDE COMMAND+ Plug-In device. Follow the setup procedure in the app.

10 Instruction Feedback Form

A feedback form has been created for the installer to provide any comments, questions or concerns about the installation instructions. The form is viewable on mobile devices by scanning the QR code or by clicking HERE if viewing on a PC.