2022 Slingshot Owner’s Manual

The engine identification number 1 is printed on the front camshaft drive cover. The number is also pin stamped on the engine block adjacent to the alternator and water pump housing 2. Record the number in the space provided in the Identification Numbers Record section.

Record important identification numbers below.

For location of the manufacturing information/vehicle identification number label, see Safety and Information Labels.

For a complete listing of the accessories that are available for your vehicle, please contact your authorized dealer or visit the online store web site.

Web Address (United States):

https://slingshot.polaris.com/en-us/shop/accessories/

As the owner, it is your obligation to ensure that the following criteria are met. It may be a violation of the Clean Air Act and the NHTSA regulations to disregard these requirements.

• When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label). Ask an authorized dealer for specific weight information.

• It is the owner’s responsibility to use the POLARIS Slingshot Accessories website as a tool for limiting the amount of accessories, based on maximum allowable vehicle weight requirements.

ALWAYS WEAR AN APPROVED FULL-FACE HELMET (DOT-certified in USA).

ALWAYS WEAR EYE PROTECTION AND A SEAT BELT.

NEVER USE WITH DRUGS OR ALCOHOL.

READ OWNER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS.

This owner’s manual contains information that is essential to the safe use and proper maintenance of your SLINGSHOT vehicle. Anyone who operates the SLINGSHOT vehicle must read the owner’s manual and all safety labels on the vehicle before operating.

• Anyone who operates the SLINGSHOT vehicle must have a valid driver’s license. In some states, SLINGSHOT vehicle operators must have a valid driver’s license with a motorcycle endorsement. Never allow anyone to operate this vehicle without the appropriate state license(s). More information on state driver’s license requirements to operate the SLINGSHOT vehicle can be found at https://slingshot.polaris.com/en-us/license-requirements/ .

• Never allow anyone under the age of 16 to operate this vehicle.

• Never install a child safety seat in this vehicle. All riders must be tall enough to sit with backs against the seat, both feet flat on the floor and seat belts properly secured.

• The driver and passenger must wear a full-face helmet (DOT-approved in US), eye protection, and seat belt at all times.

• Avoid wearing long scarves and clothing that may trail outside the rider compartment.

• Always make sure all cargo and other items in the rider compartment are properly secured before operating.

• The SLINGSHOT 3–wheel motorcycle handles differently than 2-wheel motorcycles and other on-road vehicles. Read the section in this manual entitled SLINGSHOT Vehicles vs. Other On-Road Vehicles.

• This manual was written in North America, where vehicle operation is in the right driving lane. You may need to adapt some of the instructions to the driving conditions (such as left-lane operation) and regulations in your area of operation.

• Carefully read and understand the information found in this Safety section of the owner’s manual.

• Understand and follow the procedures outlined in the Maintenance section to keep your vehicle in peak condition on the road or in storage.

• Bring this manual with you when you ride. Following the precautions and procedures in the manual will add to your enjoyment and help keep you riding safely.

• If you lose or damage this manual, you can purchase a new one through any authorized dealer. The owner’s manual should be considered part of the vehicle and remain with it if the vehicle is sold. This manual is also available online at www.polaris.com.

• If you experience a wheel impact, such as hitting a curb, a large pothole or road debris, have your tires and rims inspected immediately. These types of impacts may cause hidden tire/rim damage that may not be noticeable during operation. This damage could cause tire or rim failures and result in accidents causing serious personal injury or death. If you are in doubt, have the wheel checked by your authorized SLINGSHOT dealer or tire professional. Exercise care when parking along curbs and reduce speed if possible when approaching unavoidable potholes and/or road debris.

Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Perform all periodic maintenance at the recommended intervals outlined in the Periodic Maintenance section beginning on Maintenance Intervals. Record maintenance and service in the Maintenance Log on Maintenance Log.

Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, genuine SLINGSHOT parts are available from your SLINGSHOT dealer.

• Before each ride, perform the steps outlined in the Pre-Ride Inspections chapter.

• Always maintain proper tire pressure, tread condition and wheel and tire balance. Inspect tires regularly and replace worn or damaged tires promptly. Use only SLINGSHOT-approved replacement tires.

• Fasteners must meet original specifications for quality, finish and type to ensure safety. When inspection reveals the need for replacement parts, use genuine SLINGSHOT parts available from your SLINGSHOT dealer. Ensure that all fasteners are tightened to the proper torque.

Modifying this vehicle by removing any equipment or by adding equipment not approved by SLINGSHOT may void your warranty. Such modifications could also make the vehicle unsafe and could result in serious injury to operator or passenger, as well as damage to the vehicle. Some modifications may not be legal in your area of operation. If in doubt, your authorized dealer can answer any questions.

• Never modify this vehicle through improper installation or use of accessories that are not SLINGSHOT-approved. Use only genuine SLINGSHOT accessories designed for your SLINGSHOT vehicle.

• Do not install electrical accessories that exceed the capacity of the vehicle’s electrical system. Never install higher wattage light bulbs than those supplied as original equipment. An electrical failure could result and cause hazardous loss of engine power or lights, or damage to the electrical system.

This vehicle complies with the Canadian standard ICES-002.

Ce véhicule est conforme à la norme NMB-002 du Canada.

This vehicle does not conform to the requirements of the dynamic or static tests set out in Canada CMVSS 208 - Occupant Protection in Frontal Impacts.

Ce véhicule n’est pas conforme aux exigences des essais dynamiques ou statiques prévues par la NSVAC 208 du Canada (Systèmes de retenue des occupants en cas de collision frontale).

Always heed these fuel safety warnings when refueling or servicing the fuel system. For fuel recommendations and fueling procedures, see Fuel Recommendation.

The maximum load capacity of your vehicle is the maximum weight you may add to your vehicle without exceeding the GVWR. This capacity is determined by calculating the difference between your vehicle’s GVWR and wet weight. Refer to the Specifications chapter for details.

Refer to the manual’s Specifications section or the Manufacturing Information/VIN label on the vehicle frame for model-specific information. See the Safety and Information Labels section for details.

When determining the weight you will be adding to your vehicle, and to ensure you do not exceed the maximum load capacity, include the following:

• operator body weight

• passenger body weight

• weight of all riders’ apparel and items in or on apparel

• weight of any non-factory-installed accessories

• weight of any additional cargo on the vehicle

When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label).

Ask an authorized dealer for specific weight information if you need assistance. It is the owner’s responsibility to use the Polaris Slingshot Accessories website as a tool for limiting the amount of accessories, based on maximum allowable vehicle weight requirements. It may be a violation of the Clean Air Act or the NHTSA regulations to disregard these requirements.

For a complete listing of the accessories that are available for your vehicle, please contact your authorized dealer or visit the online store web site: Web Address (United States):
http://www.polaris.com/en-us/slingshot/shop/accessories.

If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying POLARIS in writing.

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer or POLARIS.

To contact NHTSA, or obtain other information about motor vehicle safety, you may either call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153), visit the NHTSA website at www.safercar.gov, or write to:

To report a safety defect to Transport Canada, you may either fill out an online defect complaint form at their website ( https://www.tc.gc.ca/ ) or contact their Defect Investigations and Recalls Division by calling toll-free 1-800-333-0510 (in Canada) or 819-994-3328 (Gatineau-Ottawa area or internationally).

• 1 Operation Warning Label

• 2 Tire Information Label (Canada only)

• 3 Manufacturing Information/Vehicle Identification Number Label/ICES-002

• 4 Service Information Label

• 5 Evaporative Hose Routing Label (California models)

• 6 Vehicle Emission Control Information (VECI) Label

• 7 Frontal Crash (CMVSS 208) Waiver Label

• 1 Roll Hoop (both sides)

• 2 Taillight/Brake Lights/Rear Turn Signals (both sides)

• 3 Rear Fin/Center High Mounted Stop Light (if equipped)

• 4 Fuel Cap

• 5 Seat Belts (Both Sides)

• 6 Seats (Both Sides)

• 7 Steering Wheel

• 8 Side View Mirror (both sides)

• 9 Central Main Headlight (USA)

• 10 Hood

• 11 Headlight (if equipped) / Front Turn Signal Light (both sides)

• 12 Splash Guards (both sides)

• 13 Rear View Mirror (if equipped)

• 14 Gear Selector (if equipped)

• 15 Park Brake Lever

• 16 Auxiliary 12V Outlets

• 1 Turn Signal Lever

• 2 Audio Control Buttons (if equipped)

• 3 Mode/Cruise Control Buttons

• 4 Instrument Cluster

• 5 Horn

• 6 Paddle Shifters (if equipped)

• 7 USB Port (if equipped)

• 8 Engine Start/Stop Button

• 9 Console Switches

• 10 Ride Command Display (if equipped)

• 1 Rider Information Center

• 2 Indicator Lamps

• 3 Speedometer

• 4 Tachometer

• 5 Toggle Up Button

• 6 Mode Button

• 7 Toggle Down Buttons

• The rider information center is located in the instrument cluster. All segments will light up for one second at start-up.

• The fuel gauge shows the level of fuel in the fuel tank. When the last segment clears, a low fuel warning is activated. The outline of the fuel display will flash. Refuel immediately.

If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the instrument cluster may have shut off to protect the electronic speedometer. If this occurs, your POLARIS dealer or other qualified person can provide proper diagnosis.

Welcome to Polaris Ride Command. This intuitive display includes a variety of interactive features and access to your Slingshot’s custom information.

For a safe and enjoyable riding experience with your new display, be sure to read your vehicle owner’s manual and the Ride Command User Guide. Should you need additional assistance with display operation or software updates, please see your Polaris dealer or visit ridecommand.slingshot.polaris.com.

Your Slingshot vehicle has been equipped with a Rockford Fosgate® PMX-P2 head unit.

Pinion-assisted electric power steering (PEPS) is active under certain conditions:

• If the engine is on.

• If the engine is off, electronics are active (Start/Stop button pressed twice), and the vehicle is in motion (rolling or being pushed).

When the vehicle comes to a complete stop and the engine is off, PEPS will remain engaged for 10 seconds, then it will turn off.

See the Indicator Lamps section for PEPS warning indicator information.

Open the hood to access the engine compartment. The hood release lever1 is located at the top of the grill.

1. Apply the park brake lever.

2. The hood release lever is located at the top of the grill. Pull the hood release lever upward to disengage the four hood latches.

3. To open the hood, pull up on the hood underside above the LED lamp (if equipped) using two hands. Pull the hood upward and forward, rotating the hood to a vertical position at the front of the vehicle. For Canadian units, lift from the center of the hood.

   NOTICE

   Do not pull the hood up using the plastic directly above the hood release lever. This will lead to cracking.

4. To close the hood, grasp the hood handle, push on the hood just above the front LED lights until the hood is moving on it’s own and let go of the hood. The weight of the hood will gently close the hood.

5. Apply firm downward pressure to ensure the hood is fully secured at all four latch points.

• 1 Clutch Pedal (Manual Transmission Only)

• 2 Brake Pedal

• 3 Throttle Pedal

The steering wheel can be tilted upward or downward for rider preference.

1. Pull the adjustment lever downward to unlock the steering column 1.

   

2. Move the steering wheel upward or downward to the desired position.

3. Push the adjustment lever upward to lock the steering column in position. Make sure the lever is fully seated.

The windshield provides wind protection and increased riding comfort but will not protect riders in a collision with another vehicle, the road, birds or any other object. Do not ride with a loose or damaged windshield or mounting hardware. Regularly check all fasteners for tightness.

Tighten all center windshield mount screws.

Tighten all other screws only until the wellnut begins to turn.

The fuel tank filler cap 1 is located on the left side of the vehicle, behind the driver’s seat.

Use the mirrors to assist in traffic maneuvers. Always check and adjust the mirrors before driving the vehicle. Manually adjust the mirrors by pressing on the glass. The glass rotates inside the mirror housing. Do not push or pull the mirror housing when adjusting.

Use the storage key, if equipped, to lock or unlock a storage compartment door.

The glove box compartment 1 is located on the console in front of the passenger seat. Press and release the latch button to open the door. Do not open the glove box door while operating. Stowed items could be ejected due to air movement in the vehicle.

A larger storage compartment 2 is located behind each seat. Tilt the seatback forward to access the storage compartment. When unlocked, pull abruptly on the tab located above the lock to open the door. Close the door and tap each corner abruptly to engage the rubber compression plugs.

A small storage compartment is available under the arm rest 3. Lift the lid of the arm rest to access the compartment.

The passenger footwell is equipped with a closeable vent to allow fresh air to circulate. The vent can be found in the area directly underneath the passenger storage compartment.

Use the tab 1 on the right side to open and close the vent.

This vehicle is equipped with three-point lap and diagonal seat belts on all seats. Always make sure the seat belts are secured for the driver and passenger before operating.

To wear the seat belt properly, follow this procedure:

1. For 3-point belts, pull the seat belt latch downward and across your chest toward the latch housing 1 at the outer edge of the seat. The belt should fit snugly across your hips and diagonally across your chest. Make sure the belt is not twisted.

2. Push the latch plate 3 into the latch housing until it clicks.

3. Release the strap, it will self-tighten.

   WARNING

   Failure to wear the seat belt properly could result in serious injury or death. Wear the shoulder belt on the inside shoulder only. Never wear the shoulder belt under your arm or behind your body.

4. To release the seat belt, press the square red button 2 at the center of the latch housing.

When the lock button is pushed on the key fob, the security alarm will be enabled. The alarm will sound the horn and flash headlights if the engine start/stop button is pressed or the clutch/brake is pushed when the key fob is out of range.

The security system automatically immobilizes the engine when the key fob is outside of range and enables when the key fob is within range. If the key fob is lost or not within range, a passcode must be entered to operate the vehicle.

Change the factory-set passcode to a new user passcode of your own choosing and select the desired security setting as soon as possible after receiving delivery of your new SLINGSHOT vehicle. Record your new user passcode and keep it in a safe location. Do not place your 4-digit passcode anywhere in the vehicle.

After the passcode is entered, a slight delay before the starter engages is normal.

To keep your vehicle in safe operating condition, always perform the recommended pre-ride inspections before each use of the vehicle. This is especially important before making a long trip and when removing the vehicle from storage.

You must be familiar with all instruments and controls to perform the pre-ride inspections.

When inspections reveal the need for adjustment, replacement or repair:

• refer to the maintenance section of this manual

• refer to the service manual, or

• your authorized dealer or another qualified person can assist with service

Press the engine stop/start button twice before performing the electrical pre-ride inspections. Press the button a third time to turn off the engine after completing these inspections. If inspection of any electrical item reveals component failure, repair or replace the component before operating the vehicle.

1. Position the vehicle on a level surface.

2. Press the engine start/stop button twice.

3. Observe the fuel level in the fuel gauge 1. See the Instrument Cluster section for details.

4. Refuel as needed. See Fuel Recommendation for fuel specifications.

1. Position the vehicle on a level surface.

2. Turn the steering wheel full left, then full right. The action should be smooth, but not loose.

Inspect the front suspension for oil leaks or damage. Verify smooth suspension operation.

1. Check rear shock absorber movement to ensure the correct amount of suspension travel and ground clearance. Refer to the Specifications chapter for details.

1. Check the drive belt 1 teeth for stones or other debris.

2. Inspect drive belt condition. If you discover cracks, broken teeth or frayed edges, replace the drive belt before riding. Refer to the SLINGSHOT Service Manual, or an authorized dealer can assist.

1. Inspect the entire vehicle chassis and engine for loose, damaged or missing fasteners. Tighten loose fasteners to the proper torque.

   NOTICE

   Refer to the Maintenance chapter of this manual or the service manual for fastener torque values. If needed, your dealer can assist.

2. Always replace stripped, damaged or broken fasteners before riding. POLARIS recommends genuine SLINGSHOT fasteners of equal size and strength.

In the United States, the 3-wheel SLINGSHOT vehicle is an on-road vehicle in the motorcycle class.

The SLINGSHOT vehicle handles differently than 2-wheel motorcycles, other 3-wheel vehicles and 4-wheel vehicles. The following information will help you understand the features and characteristics that make operation and handling of the SLINGSHOT vehicle different from the operation and handling of other on-road vehicles.

How does a SLINGSHOT differ from a 2-wheel motorcycle?

• Low center of gravity

• Steering wheel

• Foot controls (brake, accelerator)

• Clutch pedal (for manual transmission vehicles)

• Front suspension and steering

• Side-by-side operator and passenger seats

• Seat belts for both riders

• Lighting

• One rear drive wheel and two front wheels

The unique handling characteristics of the SLINGSHOT include:

• More stability in turns

• Flat cornering

• Turns in direction of wheel

• Quick response to steering changes

• Like all on-road vehicles, the SLINGSHOT can hydroplane (lose traction) when encountering a layer of water on the driving surface. Every vehicle has a unique hydroplane speed and response, driven by vehicle weight, tire configuration and tire condition. The SLINGSHOT may hydroplane at lower speeds and react differently to hydroplaning than most motorcycles and cars.

• All street vehicles will handle differently when operated on gravel roads. Particular attention should be payed when operating a Slingshot on gravel roads as to the position of the center, rear drive wheel relative to the crown present on many gravel roads.

• When operating at low speeds without the accelerator depressed, the AutoDrive system will engage the clutch, causing the vehicle to slow down independently of the brake pedal. This function does not replace the brake pedal. ALWAYS use the brake pedal to come to a complete stop. NEVER rely solely on engine braking to come to a complete stop.

• Making the vehicle “creep” slower than approximately 6 MPH (10 km/h) will cause the clutch to heat up and may result in overheating and excessive clutch wear.

• When slowing above 6 mph the clutch will remain engaged and the vehicle will continue to move, unless the brake is applied.

• Making the vehicle maintain position on a hill using solely the engine may cause the clutch to heat up and may result in overheating and excessive clutch wear. Always use the brakes (parking brake or foot pedal) to maintain position on a hill.

• At times, the AutoDrive system may feel different than a conventional automatic transmission. Engaging Comfort Mode or reducing throttle at the time of shift can improve smoothness.

• Unlike a conventional automatic, you will hear and feel the engine speed change during downshifts. This is normal operation.

• When cornering, the AutoDrive system may delay shifts in order to avoid upsetting the vehicle and causing loss of traction. This may result in higher than expected engine speeds, but that is normal operation. Once the vehicle has finished cornering, the AutoDrive system will continue to shift as normal.

The break-in period for your vehicle is the first 500 miles (800 km) of operation. During this break-in period, critical engine parts require special wear-in procedures so they seat and mate properly. Read, understand and follow all break-in procedures to ensure the long-term performance and durability of your engine.

Review the fuel warnings. See Fuel and Exhaust Safety. Use only the recommended fuel.

1. Insert the fuel nozzle into the fuel tank filler neck. Do not leave the nozzle unattended while fueling.

2. Fill the fuel tank until the pump stops. Do not overfill.

If the vehicle runs out of fuel, prime the fuel system before attempting to restart the engine.

1. Fill the fuel tank.

2. Press the engine start/stop button twice.

3. Allow the fuel pump to run until it stops (about 5 seconds).

4. Press the engine start/stop button once to power down the vehicle.

5. Repeat steps 2 – 3 three more times, then start the engine. See the Starting the Engine section for details.

The starter interlock system allows the engine to be started only when the clutch is disengaged (clutch pedal fully depressed) on Manual Transmission vehicles or when the brake pedal is fully depressed on AutoDrive Transmission vehicles.

If this is your first time operating the SLINGSHOT, read and understand the following sections of this manual before starting the engine:

The SLINGSHOT vehicle is equipped with a 5-speed transmission. Neutral is located between gears. When the shift lever is in neutral, it should move freely from left to right.

1. Start the engine. See the Starting the Engine section for details.

2. With the engine at idle speed and the clutch disengaged (pedal depressed), apply the brakes.

3. Move the shift lever into first gear.

4. Release the brake pedal.

5. In one smooth motion, simultaneously release the clutch pedal while slowly depressing the throttle pedal. As the clutch begins to engage, the vehicle will move forward.

6. To shift to a higher gear, accelerate smoothly to the recommended shift point. See the Recommended Shift Points section for details. Perform the following actions quickly and precisely:

   1. Simultaneously release the throttle pedal completely while disengaging the clutch (depressing the clutch pedal).

   2. Move the shift lever to the next gear.

   3. Simultaneously release the clutch pedal while depressing the throttle pedal.

   NOTICE

   Within the recommended speed ranges (see the Recommended Shift Points section for details), you can downshift to slow the vehicle or to increase power. You may want to downshift when climbing a hill or passing. Downshifting also helps to decrease speed when combined with releasing the throttle pedal.

7. To shift to a lower gear (downshift), reduce speed to the recommended shift point. See the Recommended Shift Points section for details. Perform the following actions quickly and precisely:

   1. Simultaneously release the throttle pedal completely while disengaging the clutch (depressing the clutch pedal).

   2. Move the shift lever to the next lower gear.

   3. Simultaneously release the clutch pedal while depressing the throttle pedal.

• Reduce speed before downshifting. Always downshift within the recommended shift points.

• Use extreme caution when downshifting on wet, slippery or other low traction surfaces. Release the clutch pedal very gradually in these conditions.

• Avoid downshifting in a curve. Downshift before entering the curve. Avoid coasting (clutch disengaged) through curves and corners.

The gear selector 1 is located in the center console. To change gears, stop the vehicle and, with the engine idling and the brake pedal pressed, press the button corresponding to the desired gear. Do not attempt to shift gears with engine speed above idle or while the vehicle is moving.

• R: Reverse

• N: Neutral

• D: Drive

• M: Manual (if equipped)

Paddle shifters allow manual control of forward gear changes with the AutoDrive transmission. While in manual control mode, the transmission will remain in the selected gear indicated on the rider information center even if the engine is approaching the high RPM limit. The transmission will automatically downshift to prevent engine stall.

Paddle Shifters will also work in a "semi-manual" mode while the vehicle is in drive. If a paddle shift is requested and accepted, the vehicle will shift to the requested gear and hold that gear for a short period of time or until another gear is requested.

The paddle shifters 1 are located behind the steering wheel. To upshift a gear, squeeze and release the right (+) paddle toward the steering wheel while running the engine at an appropriate RPM level. To downshift a gear, squeeze and release the left paddle (-) toward the steering wheel while maintaining the engine at an appropriate RPM level for a downshift. The transmission will not allow a downshift if the vehicle speed is too high for the gear requested.

Always allow a sufficient stopping distance so that brakes can be applied gradually. Practice braking in a safe area to become familiar with the feel of the SLINGSHOT brakes before driving in traffic.

1. To slow the vehicle, release the throttle pedal and depress the brake pedal evenly and gradually.

2. As the vehicle slows, disengage the clutch, or downshift each time vehicle speed reaches a downshift point. If braking to a complete stop, disengage the clutch when the vehicle is nearly stopped.

3. After braking to a complete stop, shift to neutral and release the clutch pedal to reduce clutch bearing wear. If stopping in traffic, keep your foot on the brake pedal so other drivers can see your vehicle’s brake lights.

Always allow a sufficient stopping distance so that brakes can be applied gradually. Practice braking in a safe area to become familiar with the feel of the SLINGSHOT brakes before driving in traffic.

1. To slow the vehicle, release the throttle pedal and depress the brake pedal evenly and gradually. The AutoDrive system will shift to lower gears as the speed decreases.

2. If stopping in traffic, keep your foot on the brake until driving may resume.

3. If stopping to park, press on the brake pedal until you come to a complete stop. Once motionless, pull up on the parking brake as far as possible, press the engine start/stop button, and then take your foot off the brake.

Accelerate by depressing the throttle pedal. For even acceleration, depress the throttle pedal smoothly. On models equipped with a manual transmission, when you reach the recommended speed for upshifting, shift up one gear.

On models equipped with the AutoDrive transmission, the AutoDrive system will select an appropriate gear based on vehicle speed and throttle input. If you wish to influence the AutoDrive to upshift, momentarily lift the throttle after accelerating.

Bring the vehicle to a complete stop before stopping the engine.

1. Brake to a complete stop. When nearly stopped, disengage the clutch.

   NOTICE

   As the vehicle slows, disengage the clutch, or downshift each time vehicle speed reaches a downshift point.

2. When fully stopped, engage the park brake.

3. Press the Engine Start/Stop button.

Bring the vehicle to a complete stop before stopping the engine.

1. Brake to a complete stop.

2. Engage the park brake.

3. Press the Engine Start/Stop button to turn off the vehicle.

   NOTICE

   Pressing the Engine Start/Stop button alone will not prevent your vehicle from moving after shutdown. Always use the park brake to prevent vehicle movement after shutdown.

When operating in cold weather at or below 40° Fahrenheit (4° Celsius), be advised that:

• The grip on your standard vehicle tires will lessen and reduce traction.

• The denser air from the lower temperatures will allow your vehicle engine to generate more power.

• The engine control program and transmission control program may compensate for lower temperatures and as a result exhibit unexpected behaviors.

• Salt and sand on roadways may reduce the grip on standard vehicle tires and damage the finish on your vehicle. If you must drive on salted/sanded pavement, POLARIS recommends washing frequently and thoroughly to remove any accumulation on your vehicle.

Follow these precautions when operating in reverse:

1. Brake to a complete stop. When nearly stopped, disengage the clutch.

2. When fully stopped, shift to neutral.

3. Always check for obstacles or people behind the vehicle, and always inspect left and right fields of vision before operating in reverse.

4. When it’s safe to proceed, shift into reverse gear. If your vehicle is equipped with a back-up camera, view the display screen for additional assistance as needed while operating in reverse. See the Back-Up Camera section for details.

5. Release the brake pedal.

6. In one smooth motion, simultaneously release the clutch pedal while slowly depressing the throttle pedal. As the clutch begins to engage, the vehicle will move rearward.

   NOTICE

   The reverse speed limit feature limits reverse operation to 10 MPH (16 km/h). Do not attempt to exceed this speed. If the engine seems to “cut out”, vehicle speed is exceeding the limit. Reduce throttle and slow down. Exceeding the limit could result in vehicle instability.

7. Never apply hard throttle while operating in reverse.

8. Always observe your path of travel and be alert to traffic, pedestrians and obstacles at all sides of the vehicle while operating in reverse.

Follow these precautions when operating in reverse:

1. Brake to a complete stop.

2. When fully stopped, press the reverse (R) button on the center console.

3. Always check for obstacles or people behind the vehicle, and always inspect left and right fields of vision before operating in reverse. If your vehicle is equipped with a reverse camera, view the display screen for additional assistance as needed while operating in reverse. See the Reverse Camera section for details.

4. When it’s safe to proceed, release the brake pedal and apply throttle slowly.

   CAUTION

   The reverse speed limit feature limits reverse operation to 10 MPH (16 km/h). Do not attempt to exceed this speed. If the engine seems to “cut out”, vehicle speed is exceeding the limit. Reduce throttle and slow down. Exceeding the limit could result in vehicle instability.

5. Always observe your path of travel and be alert to traffic, pedestrians and obstacles at all sides of the vehicle while operating in reverse.

Unless the bakes are applied, the vehicle will roll freely when on a grade.

You may use the park brake to control backwards rolling of the vehicle in steep uphill scenarios to transition from stationary to propelling forward.

In these scenarios, engage the park brake while fully depressing the brake pedal. Then, remove your foot from the brake pedal and gradually disengage the park brake as you depress the accelerator to begin moving forward.

Hill Hold control supports the driver on hill starts. The hill hold control function detects uphill start situations. After the driver releases the brake pedal, this function holds the vehicle for roughly 2 seconds, allowing the driver to simply press the throttle pedal and go.

To help prevent rolling, engage the park brake when the vehicle is parked. See the Park Brake Lever section for details. When leaving the vehicle unattended, turn the engine off and engage the park brake. To prevent unauthorized use, always take the key fob with you.

Proper maintenance assures the highest level of safety, durability and dependability for your SLINGSHOT vehicle.

Owners are responsible for performing the scheduled maintenance identified in this owner’s manual.

• Your authorized SLINGSHOT dealer can perform the break-in maintenance procedures when the vehicle’s odometer registers 500 miles (800 km).

• See your dealer or perform the recommended periodic maintenance at the intervals specified in the Periodic Maintenance Chart beginning on Periodic Maintenance.

Any qualified repair shop or person may maintain, replace, or repair the emission control devices or systems on your vehicle. An authorized POLARIS dealer can perform any service that may be necessary for your vehicle. POLARIS also recommends POLARIS parts for emissions related service. However, equivalent parts may be used for such service. It is a potential violation of the Clean Air Act if a part supplied by an aftermarket parts manufacturer reduces the effectiveness of the vehicle’s emission controls. Tampering with emission controls is prohibited by federal law.

Your dealer can perform the break-in maintenance procedures when the vehicle’s odometer registers 500 miles (800 km). Performing the break-in maintenance will help ensure optimum engine performance for the entire service life of the engine. Your dealer can change engine oil, inspect all fluids and serviceable components, ensure that all fasteners are tightened and make other adjustments as needed.

For major repair information, refer to the SLINGSHOT Service Manual. Major repairs typically require technical skills and specially designed tools. Emission system service requires special tools and training and should be performed by your dealer.

• Improperly installed or adjusted components can result in a system failure. If you do not have the time, tools and expertise necessary to complete a procedure properly, please see your dealer or another qualified person for service.

• Review the safety-related maintenance information on Safety Maintenance.

• Before beginning any maintenance procedure, read the instructions for the entire procedure.

• Always position the vehicle on a firm level surface before performing service.

• Wear eye and face protection when using pressurized air.

• Never start the engine or let it run in an enclosed area. Engine exhaust fumes are poisonous and can cause loss of consciousness or death in a short time.

• During some procedures you may use potentially hazardous products such as oil, coolant, or brake fluid. Always follow the instructions and warnings on the product packaging.

Some procedures require elevating the vehicle. DO NOT attempt to elevate your vehicle without proper equipment. If you’re not familiar with using floor jacks or lift mechanisms, see your dealer for service.

To elevate the SLINGSHOT vehicle, use automotive-quality floor jacks. Use the floor jacks on a firm, flat surface.

Make sure the floor jacks are positioned under the frame rails in the front where the lower control arm mounts to the frame, or in the rear where the frame rails meet.

For fluid changes, always make sure the elevated vehicle is level.

1 Bottom View of Lift Points

2 Side View of Lift Points

Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, we recommend genuine SLINGSHOT parts available from your dealer. However, equivalent parts may also be used, but may void your vehicle warranty. Record service and maintenance information in the Maintenance Log on Maintenance Log.

Perform maintenance at the intervals specified in the Periodic Maintenance Chart. Perform the procedures more frequently if the vehicle is subjected to severe use.

Always keep battery terminals and connections free of corrosion. If cleaning is necessary, remove corrosion with a stiff wire brush. Wash with a solution of one tablespoon baking soda and one cup water. Rinse well with tap water and dry off with clean shop towels. Coat the terminals with dielectric grease or petroleum jelly. Be careful not to allow cleaning solution or tap water into a conventional battery.

Always check and change the engine oil at the intervals outlined in the Periodic Maintenance Chart section. Always use PS4 5W-50 engine oil or another full synthetic 5W-50 high quality oil for the SLINGSHOT vehicle. See the Recommended Service Products chapter for the part numbers of recommended service products.

This fluid level does not require routine inspection. If gear shifting seems irregular or if you suspect a fluid leak, inspect the fluid level.

Always change the transmission fluid at the intervals outlined in the Periodic Maintenance Chart section. Always use SLINGSHOT Transmission Fluid or another GL-3 rated transmission fluid. See the Recommended Service Products chapter for the part numbers of recommended service products.

The fill plug is located on the left side of the gearcase. The drain plug is located on the right side of the gearcase.

This fluid level does not require routine inspection. If you suspect a fluid leak, inspect the fluid level.

Always change the angle drive fluid at the intervals outlined in the Periodic Maintenance Chart section. Always use SLINGSHOT Angle Drive Fluid or another Fully Synthetic 80w–250 fluid for the angle drive. See the Recommended Service Products chapter for the part numbers of recommended service products.

The fill plug is located on the left side of the angle drive housing. The drain plug is located on the bottom of the housing, driver’s side.

The engine coolant level is maintained by the pressurized surge tank. The surge tank system consists of the surge tank, pressure cap and associated hoses.

As coolant operating temperature increases, the expanded coolant level rises in the surge tank. As engine coolant temperature decreases, the coolant level lowers in the surge tank.

Always inspect the air filter at the intervals outlined in the Periodic Maintenance Chart. Replace the air filter every 15,000 miles (24,000 km).

1. Open the hood.

2. Clean all dirt and debris from the air box area.

3. Unlatch the air box cover clips 1 and carefully remove the air box cover.

4. Remove the air filter 2 from the air box.

5. Inspect the air filter. Shake the filter to remove excess dirt. If the filter remains caked with dirt, replace the filter with a new filter.

6. Clean the inside of the air box using a vacuum.

   NOTICE

   Avoid using compressed air for cleaning as dirt could enter the engine.

7. Reinstall the air filter or install a new air filter.

   CAUTION

   Operating the vehicle without the air filter installed can result in serious engine damage, which could result in an accident and injury to the operator and others. Always make sure the air filter is installed.

8. Reinstall the air box cover and secure the clips.

9. Close the hood.

Adjust drive belt tension after the first 2,500 miles (4,000 km) of operation. Replace the drive belt 1 and both sprockets as a set if the drive belt has over 30,000 miles (48,000 km) of service at the time of damage or failure.

When inspecting the drive belt for signs of wear, refer to the Drive Belt Wear Analysis table on the next page to determine whether the belt needs to be replaced. See the SLINGSHOT Service Manual or an authorized dealer for more information.

DO NOT attempt to check belt tension if the belt has been exposed to rain or washing within a 24 hour period or if the belt is hot from being in use. Allow the belt to cool down to ambient temperature before measuring belt tension.

Cleaning the drive belt will maximize belt and sprocket life and minimize drive line noise. Clean the belt at every tire change. Clean the belt more often if operating in dirty, dusty or high debris environments.

1. Mix a few drops of mild dish soap with a cup of warm water.

2. Use a soft nylon brush to clean the belt and sprocket teeth with the soapy water. Clean well in corner areas where road debris and belt dust can collect.

3. Rinse the belt with clear water, then dry thoroughly.

Always inspect the suspensions at the intervals outlined in the Periodic Maintenance Chart beginning on Periodic Maintenance. Refer to the SLINGSHOT Service Manual, or your authorized dealer can assist.

Inspect fuel lines and connections for wear, deterioration, kinks, leaks, or other damage. If any leaks or damage of fuel system components are found, do not operate the vehicle. Promptly see your dealer for service if any of these conditions exist.

The “check engine” indicator illuminates if a purge valve fault is present. See your authorized dealer for service.

Inspect the entire length of both crankcase breather hoses for cracks, kinks, wear or other damage. Make sure clamps are in place and secure.

• 1 Fresh Air Side

• 2 PCV Side

The clutch fluid reservoir 1 is located under the hood on the driver’s side of the vehicle. Check the hydraulic clutch fluid level before each use of the vehicle. Maintain the fluid level between the MIN and MAX lines on the reservoir.

Use DOT 4 brake fluid in the hydraulic clutch fluid reservoir. Use fluid only from a sealed, clean container. Review the brake fluid precautions on Brake Fluid Precautions.

The brake fluid master cylinder reservoir 1 is located under the hood on the driver’s side of the vehicle. Check the brake fluid level before each use of the vehicle. Maintain the fluid level between the MIN and MAX lines on the reservoir.

If the BRAKE FAILURE indicator illuminates, brake fluid may be low. Check the brake fluid level.

Use DOT 4 brake fluid in the brake fluid reservoir. Use fluid only from a sealed, clean container.

1. Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. See the SLINGSHOT Service Manual or your authorized dealer.

2. Check the brake pedal for excessive travel or a spongy feel.

3. Inspect the rotor to ensure tightness to hub.

4. Check the brake pads for wear, damage and looseness.

5. Inspect brake discs for nicks, scratches, cracks or other damage. Clean any grease using an approved brake cleaner or alcohol.

   WARNING

   Do not apply WD-40® or any petroleum product to brake discs. These types of products are flammable and may also reduce the friction between the brake pad and caliper.

6. Inspect the brake disc spline and pad wear surface for excessive wear. Change pads when worn to 3/50'' (1.5 mm).

7. Inspect the thickness of each brake disc at four or more locations around the disc. If any disc is worn to the minimum thickness at the thinnest point, or if a disc is damaged, see your dealer for replacement.

8. The R model comes with a 2–piece rotor. Check that the rotor is tightened adequately to the hub.

3/50'' (1.5 mm)

Minimum Thickness Front: 19 mm / Rear: 19 mm

An engine compression test can be performed to monitor general engine condition. Refer to the SLINGSHOT Service Manual, or your authorized dealer can assist.

Check the exhaust system for visible and audible signs of exhaust gas leaks. Check that all fasteners, springs, and rubber isolators are in place and in good condition. Check that exhaust heat shields are in place and not damaged or deteriorated. If any exhaust leaks or missing/deteriorated components (including heat shields) are found, do not operate the vehicle. Perform necessary repairs before continuing vehicle operation. Refer to the SLINGSHOT Service Manual, or your authorized dealer can assist.

This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new SLINGSHOT vehicle. We recommend the use of Polaris Engineered Vehicle Care cleaning and polishing products to offer the best care for your vehicle. Polaris Engineering Vehicle Care can be found online at https://www.polaris.com/en-us/ or at your Polaris SLINGSHOT Dealer. After cleaning the vehicle, inspect for damage to the painted surfaces. Repair chips or scratches promptly by applying touch-up paint to prevent corrosion.

For more information, or for answers to your cleaning and detailing questions, please see your SLINGSHOT dealer.

1. Do not use abrasive cleaners.

2. Rinse off as much dirt and debris as possible with water running at low pressure. Use as little water as possible when washing near the air intake or the exhaust pipe openings. Dry these components thoroughly before using the vehicle.

3. Make sure the brakes are functioning properly before riding.

If you will not operate the vehicle for 60 days or longer, such as during the winter, storing it properly will help prevent damage to the fuel system, electrical system, engine, suspensions, tires and body. During extended storage periods, maintain tire pressure and battery voltage at the recommended levels.

1. Choose a dry, well-ventilated storage location away from direct sunlight, preferably a garage or similar structure. The structure should have a firm, flat, clean surface free of oil and gasoline. The structure should have a relatively constant and moderate temperature.

2. Proper storage starts with cleaning, washing and waxing the hood, chassis, upholstery and plastic parts. Be sure that corrosive salt and acids are removed from surfaces before beginning preservation with waxes and rust inhibitors (grease, oil or paint). Clean and touch up with paint any rusted or previously painted surfaces.

3. Apply a light coat of oil or grease to all bushings, spindle shafts and tie rod ends.

4. Change the engine oil. Start the engine and allow it to idle just long enough to circulate the new oil throughout the engine.

5. Store the vehicle with a full tank of non-oxygenated fuel. If non-oxygenated fuel is unavailable, a commercial oxygenated fuel is acceptable. Note that most oxygenated fuels contain ethanol. Since ethanol is hydroscopic, oxygenated fuel will absorb water vapor during storage. Completely filling the tank fuel minimizes the exposure and absorption of water vapor during seasonal storage. Fuel to be treated with a fuel stabilizer, Polaris Advanced Fuel Treatment additive 2881416 or equivalent.

6. Remove the spark plugs. Spray a light amount of engine fogging oil into each cylinder to prevent rust. Reinstall the plugs.

7. Make sure the coolant quality and level in the system is adequate for freeze protection during storage.

8. Apply a metal protectant to shock absorber shafts or any exposed metal to prevent corrosion.

9. Separate electrical connector blocks and clean corrosive build-up from connectors. Replace worn or frayed electrical wire and connectors.

10. Prepare the battery for storage.

11. Verify that tire pressure is at specification.

12. Cover intake and exhaust openings to prevent small animals from entering.

13. Elevate the vehicle using appropriate jack stands. Remove the wheels to prevent flat spots on the tires.

14. Do not engage the park brake. If engaged, the brake pads may stick to the discs.

15. Cover the vehicle with a fabric cover. Do not use plastic or vinyl covers, which trap moisture and encourage rust and corrosion.

1. Have the battery removed by an authorized dealer.

2. Clean the battery terminals first with a wire brush to remove any loose deposits.

3. Wash the posts and the ends of the battery cables with a solution of one part baking soda to 16 parts water. Rinse with clean water and wipe dry.

4. Apply a thin film of dielectric grease to the posts and cable connectors.

5. Clean the outside of the battery with a solution of mild detergent and warm water.

6. Store the battery in a dry area with a temperature of 32° to 90° F (0° to 32° C).

7. While in storage, fully charge the battery once a month.

1. Remove the fabric cover.

2. Remove intake and exhaust opening covers (if covered for storage).

3. Install the tires. Lower the vehicle and remove the jack stands.

4. Verify that tire pressure is at specification. Refer to safety labels on the vehicle or to the Specifications chapter.

5. Install the battery and perform an electrical inspection.

6. Inspect the spark plugs. Install new spark plugs if necessary.

7. If the vehicle was stored in an area subject to wide swings in temperature and humidity (such as outdoors), change the engine oil before starting the engine.

   NOTICE

   During storage, temperature and humidity changes can cause condensation to form in the crankcase and mix with engine oil. Running the engine with oil that contains condensation can cause engine damage.

8. Inspect the storage area for signs of fluid leaks. Identify and perform service to any leaking components.

9. Wash and polish the vehicle. Wax, polish or apply protectant to appropriate components.

10. Perform the pre-ride inspections. See the Pre-Ride Inspections chapter for details.

11. Check any fluid levels not included in the pre-ride inspection.

Because of the single rear wheel on the SLINGSHOT vehicle, it cannot be towed by a conventional tow truck. Never tow the SLINGSHOT vehicle on its wheels behind another vehicle.

To transport the SLINGSHOT vehicle, always use a trailer or flatbed truck. A trailer must have an approved load rating greater than the actual weight of the SLINGSHOT vehicle, including any installed accessories or cargo.

Follow these guidelines after loading the SLINGSHOT vehicle on a trailer or flatbed truck.

1. Place the transmission in gear.

2. Engage the park brake.

3. Press the engine start/stop button to turn the engine off.

4. Secure all cargo and other items or remove them from the vehicle.

5. Secure all storage compartment doors.

6. Block all wheels at the front and rear of each tire.

1. Always secure the frame of the SLINGSHOT vehicle to the transporting unit securely with suitable tie-down straps. Do not attach straps to the lower front trim. Secure the tie-down straps to the lower front A-arms 1 and rear swing-arm 2. See illustration.

1. Never allow passengers on a trailer or in a trailered vehicle.

2. Reduce speed and drive with caution while transporting.

For your personal safety, do not attempt inspection or repairs not fully described in this owner’s manual. Contact an authorized dealer or another qualified person for service if you cannot determine the cause of a problem or if the inspection / repair exceeds your mechanical ability or tool resources. Do not perform any inspection or repair with the engine running.