Accessory Installation

All 2015–2017 Indian^® Scout^® Models

(For All 2018 Indian^® Scout^® Models, skip to section Speedometer Mount Replacement)

(For 2019 and Newer Indian^® Scout^® Sixty Models, skip to section USB Connection Installation)

1. Move fuse box to access battery terminals. Remove and retain screw A and remove negative (-) battery cable B from battery terminal. Position cable well clear of terminal. Remove rubber cover C from positive (+) battery cable D. Remove and retain screw E and remove positive (+) battery cable. Position cable well clear of terminal.

   WARNING

   Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When disconnecting battery, always disconnect the negative (black) cable first. When reconnecting battery, always connect negative (black) cable last.
   

2. Route new wiring harness 2 through two existing cable ties F. (If cable ties are missing, install new cable ties in locations shown.) Place wires so length will allow for connection to battery terminals.

   

3. Connect positive (+) battery cable C and positive end of new USB wire 2. Secure using retained screw E. Torque screw to specification.

   TORQUE

   Positive (+) Battery Terminal Screw E:

   45 in-lbs (5 N·m)

4. Connect negative (-) battery cable B and negative end of new USB wire 2. Secure using retained screw A. Torque screw to specification.

   TORQUE

   Negative (-) Battery Terminal Screw A:

   45 in-lbs (5 N·m)

5. Continue to run wire 2 to front of vehicle. Route around fuel fitting G as shown.

   

6. Route wiring 2 under upper frame H. Secure wire to main harness with cable tie 4.

   

7. Route wiring 2 behind frame H and secure to existing harness K with new cable tie 4. Continue to route wire 2 behind fork J toward headlight housing.

   

8. Insert wire end 2 into opening on rear of headlight housing K and pull through opening into headlight housing..

   

9. Replace any cable ties that were removed during installation.

10. Return fuse box to original position.

All 2015–2018 Indian^® Scout^® and Scout^® Bobber Models

1. Remove and retain two screws A and separate speedometer B from speedometer mount C. Discard speedometer mount C.

   

2. Insert speedometer B into new speedometer mount 3 and secure with two retained screws. Torque screws to specification.

   TORQUE

   Speedometer Screw A:

   16 in-lbs (1.8 N·m)
   

USB Module Installation (All Models)

1. Slide collar A off USB module 1 and hold inside speedometer mount. Insert USB module 1 through collar A until a click is heard. Make sure collar is secure.

   

2. Plug speedometer connector into speedometer. Make sure USB wiring is routed properly and reinstall speedometer mount assembly B using four retained bolts C (removed in Step 1 of Speedometer Mount Removal section.) Torque bolts to specification.

   TORQUE

   Speedometer Mount Bolt C:

   22 ft-lbs (29 N·m)
   

Connect USB Module

1. Plug USB module connector 1 into either newly run USB power wire 2 (All MY 2018 and Older Indian^® Scout^® Models) or into already present USB power cable D (2019 and newer Indian ^® Scout^® Sixty)

   

2. Reconnect wiring in headlight assembly and reassemble headlight. Torque headlight retaining ring screw to specification.

   TORQUE

   Headlight Retaining Ring Screw:

   33 in-lbs (4 N·m)

1. Route USB module connector 1 into cloth cable wrap E. Plug USB module connector 1 into already present USB power cable D. Close and secure cloth wrap E.

   

2. Reinstall headlight nacelle and brackets with six retained screws. Torque screws to specification.

   TORQUE

   Headlight Nacelle Bracket Screw:

   84 in-lbs (9.5 N·m)