|
Cruise Control Enabled |
Before using the cruise control, read the safety
and operation procedures. See Operating Cruise Control. |
|
Cruise Control Engaged |
Before using the cruise control, read the safety and operation
procedures. See Operating Cruise Control. |
|
Anti-Lock Brake System |
Your dealer can assist if this lamp remains on. When the lamp
is illuminated, the anti-lock brakes will not activate, but the conventional
brake system will continue to operate normally. |
|
High Beam |
This lamp illuminates when the headlamp switch is set to high
beam. |
|
Turn Signal / Hazard Signals |
The turn signals are located at the top center of the instrument
cluster. Arrows flash when either a turn signal or the hazard signal
is activated. If a lamp fails, or if there is a short circuit in
the signal system, the lamp flashes at more than twice the normal
rate.
|
|
Low Fuel |
This lamp illuminates when approximately one gallon (3.8 liters)
of fuel remains in the fuel tank. |
|
Engine Overheat |
This lamp illuminates to indicate an overheated engine. If
the indicator flashes, the overheating condition remains, and the
system will automatically reduce engine power. |
|
Check Engine |
If this lamp illuminates while the engine is running, promptly
contact an authorized dealer or another qualified person who can assist
with diagnosis. If abnormal engine operation is detected the light
will remain on as long as the fault condition exists. Retrieve the
error codes for diagnosis. See the Error Codes section for details.
This lamp is also known as a malfunction indicator lamp (MIL). |
|
Low Battery Voltage |
This lamp illuminates when battery voltage is low (or when
voltage is above the normal range). Turn non-essential accessories
off to conserve power. Make sure the charging system is operating
properly. |
|
Traction Control |
This lamp illuminates if the user disables traction control
with the ESP Switch. See Electronic Stability Program (ESP) Switch. |
|
ESP Disabled |
This lamp illuminates if the user disables the ESP (Electronic
Stability Program) with the ESP Switch. Always enable the ESP for
normal operation. See Electronic Stability Program (ESP) Switch. |
|
ESP Intervention |
The ESP (Electronic Stability Program) intervention lamp flashes when the ESP is actively assisting. The lamp illuminates solid to indicate a system fault and the ESP will be disabled.
If the lamp illuminates solid, your dealer can inspect the vehicle
and perform service. A flashing ESP icon indicates that the ESP is
intervening to maintain control of the SLINGSHOT. Modify your driving
behavior if this occurs. Slow down and reduce steering inputs. |
|
Brake Failure |
This lamp illuminates if a brake component is not operating
properly. Do not operate the vehicle. Inspect brake fluid levels.
Your dealer can inspect the vehicle and perform service. |
|
Seat Belt |
The seat belt lamp illuminates whenever the vehicle is in ignition
state and the driver’s seat belt is not fastened. |
|
Pinion-Assisted Electric Power Steering Warning |
This lamp illuminates briefly when the vehicle is in ignition
state. If ignition state is activated for 5 minutes without starting
the engine, the lamp illuminates to indicate that the PEPS has shut
down to conserve battery power. If the lamp illuminates after starting
the engine, the power steering system is inoperative. Your dealer
can inspect the vehicle and perform service if the lamp illuminates
after starting the engine. |
|
Park Brake Engaged |
This lamp illuminates when the park brake is engaged. If it
illuminates when the park brake is NOT engaged, your dealer can inspect
the vehicle and perform service |
|
Low Oil Pressure |
This lamp illuminates if engine oil pressure drops below safe
operating pressure. If this lamp illuminates while the engine is running,
turn the engine off as soon as safely possible and check the oil level. If the oil level is correct and the lamp remains on after the engine
is restarted, turn the engine off immediately.
|
|
Chassis Warning |
If a fault condition is detected, the light
will remain on as long as the condition exists. Retrieve the error
codes for diagnosis. This lamp is also known as an Amber Warning Lamp
(AWL). |
|
Transmission Control Module (TCM) Fault Warning |
If a fault condition is detected, the light
will remain on as long as the condition exists. Retrieve the error
codes for diagnosis. |